Atdec TH-3070-UF flat panel wall mount manual

Atdec TH-3070-UF flat panel wall mount
(1)
  • Number of pages: 2
  • Filetype: PDF
  • Bits Bag
    Component Checklist

    Installation Instructions

    FLAT SCREEN WALL MOUNT | FIXEDTH-3070-UF

    Display Bracket (x2)
    Wall Plate
    Important Notes
    TOOLS REQUIRED:
    

    Power Drill

    

    12mm (

    1
    /
    2

    ”), 10mm (

    3
    /
    8

    ”) or 7mm (

    1
    /
    4

    ”) Drill Bit

    

    Phillips Head Screw Driver

    

    Spirit Level

    

    17mm (

    11
    /
    16

    ”) Socket Wrench or Shifter

    Supports a maximum load of 91kgs (200lbs).

    Suits displays with mounting hole patterns from 180mm to 810mm wide (7”-31

    3
    /
    4

    ”) by 125mm to 500mm

    high (5”-19

    1
    /
    2
    ”).

    The manufacturer does not accept responsibility for incorrect installation.

    Security Bracket
    Mounting Screws
    M8x15mm / M8x35mm / M8x45mm (x4 each)
    M6x15mm / M6x35mm / M6x45mm (x4 each)
    M5x15mm / M5x35mm / M5x45mm (x4 each)
    M4x15mm / M4x35mm / M4x45mm (x4 each)
    Cross Recessed Screws
    Coach
    Screw (x4)
    Masonry Wall
    Plug (x4)
    Washer (x4)
    Multi
    Washer (x4)
    Dry Wall
    Anchor (x6)
    Mounting the Wall Plate
    A
    Masonry Wall
    Washer
    Masonry
    Wall Plug
    Wall Plate
    12mm (
    1
    /
    2
    ”)
    Hole
    Coach Screw
    Dry Wall Timber Stud Wall
    TIP: Use a spirit level to
    ensure the wall plate is
    horizontal
    TIP: Use a spirit level to
    ensure the wall plate is
    horizontal
    TIP: Use a spirit level to
    ensure the wall plate is
    horizontal
    Wall Plate
    Coach Screw
    Washer
    Timber
    Stud
    10mm (
    3
    /
    8
    ”)
    Hole
    Wall Plate
    Dry Wall
    Anchor
    Dry Wall
    Anchor Screw
    Dry Wall
    Anchor Washer
    Use a stud finder to precisely
    locate the timber stud and
    ensure that the mounting holes
    are located in the centre of
    the stud.
    It is recommended when
    mounting directly into masonry
    wall, that the mounting holes
    are positioned as far apart as
    possible.
    7mm (
    1
    /
    4
    ”)
    Hole
    Note: Ensure the Wall Plate
    is mounted with the folded
    tabs pointing upwards.
    Note: Ensure the Wall Plate
    is mounted with the folded
    tabs pointing upwards.
    Note: Ensure the Wall Plate
    is mounted with the folded
    tabs pointing upwards.
    The dry wall anchors provided in
    the bit bag have been tested for
    this wall mount application and will
    each hold in excess of 30kg per
    anchor.
    Before using the expanding
    anchors, please ensure that you:
    · Check the plaster board wall (dry
    wall) is in good condition with no
    cracks, peeling paper or signs of
    water damage etc.
    · Take care installing the anchors,
    that they are not over tightened
    or driven into the wall during
    installation.
    · Minimum thickness of drywall
    should be no less than 12mm (
    1
    /
    2
    ”)
    · Recommend to use all 6 anchors
    even with light monitor applications.
    · Only use the anchors supplied
    in the kit.
    · Make sure the 10mm (
    3
    /
    8
    ”) pre-
    drilled hole is as recommended and
    no smaller or larger.
    · The anchors during expansion
    should not interfere with studs or
    noggins (cross strengtheners).
    13mm Spacer
    Bush (x4)
    20mm Spacer
    Bush (x4)
Atdec TH-3070-UF flat panel wall mount

Need help?

Number of questions: 0

Do you have a question about the Atdec TH-3070-UF flat panel wall mount or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Atdec TH-3070-UF flat panel wall mount owners to properly answer your question.

View the manual for the Atdec TH-3070-UF flat panel wall mount here, for free. This manual comes under the category Flat panel support and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Atdec TH-3070-UF flat panel wall mount or do you need help? Ask your question here

Atdec TH-3070-UF flat panel wall mount specifications

General
Brand Atdec
Model TH-3070-UF flat panel wall mount
Product Flat panel support
EAN 163120465156, 881493004771, 971477722972
Language English
Filetype PDF
Design
Product colour Black
Weight & dimensions
Width 845 mm
Depth 34 mm
Height 535 mm
Other features
Screen size compatibility 32 - 65 "
Weight (imperial) 200 lbs
Weight (max) 91 kg
Mounting interface VESA 100mm x 200mm / 200mm x 200mm, nonVESA 180mm x 800mm / 100mm x 500mm
Mounting
Mounting type Wall