Atdec VF-AT-D manual

Atdec VF-AT-D
(1)
  • Number of pages: 2
  • Filetype: PDF
  • A Component Checklist - Check you have received all parts against the component checklist prior to installing

    Bolt Through

    Installation Instructions

    Steel washer
    Bolt
    Through Base
    M8 Desk Clamp Screw
    (found
    in the Desk
    Clamp
    Box)
    5mm
    Allen
    Key
    9mm (³/
    8
    ”) Hole
    Drill a 9mm /
    8
    ”) hole in the
    work surface at the desired
    position
    and assemble as
    shown
    below.
    NOTE:
    Ensure the slot in the Pole Assembly faces away
    from the user.
    It is recommended that the Pole Assembly be
    mounted towards the rear edge of the work surface

    IMPORTANT:

    The “User Operating Card”

    must

    be left

    with

    Visidec Focus Articulated

    Arm

    Double once installed

    Desk Clamp

    Pole Assembly
    B1
    B2
    m
    o
    t
    t
    o
    B
    Slot
    NOTE: When using the Desk Clamp mounting option,
    the displays can only be used in side by side
    configuration as shown. Failure to do so may result in
    serious damage to product and displays.
    Tighten Firmly
    Double
    Arm
    Assembly
    Pole Assembly
    User
    Operating Card
    (see
    note at top of page)
    m
    o
    t
    t
    o
    B
    p
    o
    T

    Desk Clamp Box

    5mm Allen
    Key
    Desk
    Clamp Bracket
    M8 Desk
    Clamp
    Screw

    Bits Box

    Primary Arm
    Cable
    Cover (x2)
    Secondary Arm
    Cable
    Cover (x2)
    Bolt Through
    Base
    Steel
    Washer
    M8x30mm
    Screw
    Pole Top
    Cap
    Cable Clip (x2)
    Display
    Mounting
    Screws
    M4x16mm
    (x8)
    M4x12mm
    (x8)
    M4x10mm
    (x8)
    Cable
    Balls
    (x2)
    Work Surface
    Pole
    Assembly
    Step 3: Adjust the height of the Pressure Plate to suit the
    Work Surface and tighten firmly in the desired location.
    5mm
    Allen Key
    Tighten
    Firmly
    Step 1: Attach the Desk Clamp Bracket to the bottom
    of
    the Pole Assembly using the M8x30mm Screw.
    Tighten
    firmly using the 5mm Allen Key.
    Ensure
    the Visidec logo is facing the front as shown.
    M8x30mm
    Screw
    m
    o
    t
    to
    B
    Step 2: Install the M8 Desk Clamp
    Screw and Pressure Plate as shown.
    Desk
    Clamp
    Bracket
    5mm
    Allen
    Key
    Bolt
    Thru
    Base
    Pole
    Assembly
    Pressure
    Plate
    M8
    Desk
    Clamp
    Screw
    5mm
    Allen
    Key
    NOTE: It is recommended that the Pole
    Assembly be clamped to the rear or side
    edge of the work surface
    Suits 12mm ”)
    to 38mm (1½”)
    thick work
    surfaces
    ADJUSTMENT RANGE
    Pressure Plate
    Tighten
    Firmly
Atdec VF-AT-D

Need help?

Number of questions: 0

Do you have a question about the Atdec VF-AT-D or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Atdec VF-AT-D owners to properly answer your question.

View the manual for the Atdec VF-AT-D here, for free. This manual comes under the category Flat panel support and has been rated by 1 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Atdec VF-AT-D or do you need help? Ask your question here

Atdec VF-AT-D specifications

General
Brand Atdec
Model VF-AT-D
Product Flat panel support
EAN 132017773117, 163120472512, 720286911462, 881493004351
Language English
Filetype PDF
Mounting
Maximum weight capacity 8 kg
Mounting type Desk
Other features
Mounting interface VESA 75mm x 75mm / 100mm x 100mm
Lift 31.5 cm
Ergonomics
Tilt angle range -70 - 70 °
Pan range 0 - 180 °
Angle of rotation 240 °
Design
Product colour Silver
Weight & dimensions
Weight (imperial) 17.5 lbs