Chamberlain KLIK1U manual

Chamberlain KLIK1U
(1)
  • Number of pages: 2
  • Filetype: PDF
  • ON
    2 3
    1
    KG
    KG
    12 11 10 9 8 5 3 7 6 4 1 2

    CLICKER

    ®
    MODEL KLIK1U
    UNIVERSAL GARAGE DOOR OPENER REMOTE CONTROLRead instructions thoroughly BEFORE beginning.Start with garage door closed. Identify garage door opener type - Smart/Learn button or DIP Switch. Smart/Learn button or DIP Switches are located on motor unit or external receiver. Refer to owner’s manual if necessary.Clicker products are intended to be used only with garage door openers manufactured after 1993 that utilize photo-eyes safety sensors. These are always located on or near the bottom of the door track. If your garage door does not have the sensors attached and working, the opener is not compliant with current federal safety regulations and should be replaced.Proceed with instructions according to your type of garage door opener.To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. © 2011, Clicker Corporation114A3485G All Rights Reserved
    OR

    DIP SWITCH SMART/LEARN BUTTON

    REMOTE CONTROL BATTERYNOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Dispose of batteries properly. Replace ONLY with 3V2032 coin batteries.To prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediately notify doctor.To reduce risk of fire, explosion or chemical burn:• Replace ONLY with 3V2032 coin batteries.• DO NOT recharge, disassemble, heat above 100° C (212° F) or incinerate.Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie and Intellicode are trademarks of GMI Holdings, Inc. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.DIP SWITCH SMART/LEARN BUTTON
    3
    Press program button until LED lights.
    1
    See Chart A to determine # of times to press button and write in blank on Step 5.
    1
    See Chart B to determine # of times to press button and write in blank on Step 5.
    * NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible with
    Chamberlain technology.
    **NOTE: Visit www.clickerproducts.com for Genie Intellicode II instructions.
    Product Registration and Troubleshootingwww.clickerproducts.com • 1-800-442-1255LED IndicatorButton 1Button 2Program ButtonBatteryDIP SwitchesBattery Cover NOTE: 2 Position DIP Switch: If programming fails reverse DIP switches (OFF to ON and ON to OFF).** 3 Position DIP Switch:For Chamberlain remotes DO NOT use the “0” position, use “+” or “-”. If you already have a 3-button remote, DIP switch #1 must be set to “-” if the large button is to open the door. It may be necessary to reprogram original remote controls.
    ON
    STOP
    CHART B# of times to press button Brand Description Year11 Chamberlain
    ®
    * 9 Position '90-'9212 Chamberlain
    ®
    *
    9 PositionCanada'83-'8913 Genie
    ®
    12 Position '8514 Linear Multicode
    ®
    10 Position '7615 Chamberlain
    ®
    8 Position '83-'89
    16
    Stanley/Multicode
    ®
    10 Position '7617 Genie
    ®
    9 Position '85
    18
    Linear
    ®
    Moore-O-Matic
    ®
    8 Position '7619 Chamberlain
    ®
    7 Position '83-'89CHART A# of times to press button BrandType/Color of Smart/Learn Year1 Linear
    ®
    Mega-Code '97-Current2 Chamberlain
    ®
    * Orange/Red '97-'033 Chamberlain
    ®
    * Purple '05-Current4 Chamberlain
    ®
    * Green '93-'96
    5
    Genie
    ®
    Overhead Door
    ®
    Intellicode '95-Current
    6
    Genie
    ®
    **
    Overhead Door
    ®
    Intellicode '93-Current7 Stanley
    ®
    Secure Code '988 Chamberlain
    ®
    * Yellow '11-Current9 Wayne Dalton
    ®
    Rolling Code '9911 Chamberlain
    ®
    9 Position '90-'92
    2
    2
    Programming complete. Press selected button to test. If unit does not work, return to Step 3.
    7
    Programming complete. Press selected button to test. If unit does not work, return to Step 3.
    7
    Press program button.
    6
    Press program button.
    6
    5
    OR
    OR
    ClickNOTE: If there are problems programming to button 1, program to button 2.Select a button to program. Press button times ensuring LED stops flashing after each press. Code is accepted when one of the following occurs:
    2 3
    1
    KG
    KG
    Press and release the Smart/Learn button.Motor Unit
    4
    12 11 10 9 8 5 3 7 6 4 1 2
    3
    Match DIP switches. Turn extra switches OFF.**Motor
    Unit
    Existing RemoteClicker Remote
    4
    Press program button until LED lights.
    5
    Select a button to program. Press button times ensuring LED stops flashing after each press. Code is accepted when door activates.NOTE: Your opener may appear different and you may have to remove the light lens to access the learn button.
    2
Chamberlain KLIK1U

Need help?

Number of questions: 0

Do you have a question about the Chamberlain KLIK1U or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Chamberlain KLIK1U owners to properly answer your question.

View the manual for the Chamberlain KLIK1U here, for free. This manual comes under the category Remote Controllers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Chamberlain KLIK1U or do you need help? Ask your question here

Chamberlain KLIK1U specifications

General
Brand Chamberlain
Model KLIK1U
Product Remote Controller
EAN 787083554513, 88021215344, 999993034621
Language English
Filetype PDF
Performance
Number of devices supported 2
Maximum range - m
Transmitting LEDs 1
Design
Interface -
Product colour Black,Grey
Compatibility Genie\r\nLinear/Moore-o-Matic\r\nStanley\r\nOverhead Door\r\nWayne-Dalton\r\nCraftsman\r\nChamberlain\r\nLiftMaster\r\n300/310/315/372/390 MHz
Input type Press buttons
Display
Built-in display
Weight & dimensions
Weight - g
Battery
Built-in battery
Rechargeable
Battery technology Lithium
Battery type CR2032
Number of batteries supported 1
Indication
Battery low indication

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Chamberlain KLIK1U.

Is your question not listed? Ask your question here