Smeg KSEP920X manual

Smeg KSEP920X
(1)
  • Number of pages: 8
  • Filetype: PDF
  • WARNING!
    Read the instructions carefully before installing and/or using the hood.
    Before connecting, make sure that the mains voltage corresponds to the voltage on
    the rating plate inside the hood. (see fig. 7)
    Once you remove the appliance from its packaging make sure it is intact. If the
    product is damaged, do not use it and contact the Smeg assistance network.
    It is recommended that a qualified technician performs installation and adjustment
    operations.
    The minimum distance between the cooker and the lower part of the hood must be
    750mm for gas cookers and 650 mm for electric cookers.
    Before carrying out any kind of maintenance or cleaning, disconnect the hood from
    the mains supply.
    Inspect and clean the filters thoroughly and in accordance with the intervals
    suggested by the manufacturer.
    Do not cook or fry in a way that could result in flames being sucked into the hood and
    causing a fire.
    The hood surface can be cleaned with a damp cloth and a non-bleach liquid
    detergent.
    Make sure the room is properly ventilated when using the hood and other gas
    appliances at the same time.
    Comply with the regulations on air discharge when operating the hood.
    The extracted air must not be routed into a duct used to discharge fumes of gas-
    operated appliances.
    This appliance must not be used by children without an adult supervision

    and disabled people may require assistance.

    THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE ABOVE
    INSTRUCTIONS ARE NOT FOLLOWED.

    OPERATION

    This appliance has been designed to work as a
    DUCTING
    hood (evacuation of the
    air) or RECYCLING hood (recycling of the filtered air).
    DUCTED MODE: In order to use the hood in the ducted mode, connect the motor
    intake, by means of a suitable ducting hose not less than 120mm diameter, directly to
    the external fumes outlet.
    Note: Remove any carbon filters.
    RECIRCULATION MODE: If it is not possible to discharge fumes outside, the hood
    can be used to filter and recycle the air. This way, air and fumes are filtered by the
    anti-odour carbon filters and recirculated through the aerating grids on the sides of
    chimney.

    EN 01

    INSTALLATION INSTRUCTIONS:

    The hood is supplied with all the necessary
    accessories for installation. The minimum distance
    between the cooker and the lower part of the hood
    must be 750 mm for gas cookers and 650 mm for
    electric cookers (Fig. 1). The hood is supplied with a
    motor intake (Fig 2). If it has not been assembled by
    the manufacturer, you can assemble it using the
    supplied screws (for type 1) or pushing (for type 2)
    If the motor intake is equipped with a non-return
    valve, make sure it opens and closes perfectly.
    The following instructions will assist installation:
    a) The hood should be centred with respect to the
    cooker.
    b)
    The hood is supplied with two supports/hooks (a)
    (Fig 3) or bracket (b) that need to be fixed to the
    wall by means of wall anchors . The L1 holes for
    these supports are on the back of the hood (fig.
    4)
    c)
    Remove the anti-grease filters, put the hood on
    the wall and mark the position of the holes for the
    supports/hooks.
    d) Drill the two previously marked holes after
    removing the hood from the wall.
    e) Fix the two supports/hooks to the wall.
    f) Mark the L2 holes on the wall to fix the hood
    safely. (fig. 4) Drill and put the anchors in the
    holes.
    g) Hang the hood on to the supports/hooks (fig. 5)
    and level by means of the adjusting screw
    (fig.3).
    h) Fix the hood safe by tightening both wall anchors.
    Ducted mode or Recirculation mode installation:
    Ducted mode:
    In the ducted mode, connect the motor outlet to the
    fumes outlet duct not less than 120mm diameter.
    Warning: if the hood is equipped with an active
    carbon filter, it must be removed (see page 7)

    EN 02

    Fig.2

    Hood levelling screw

    Fig.3

    Type 1

    Type 2

    Fig.1

    (a)
    (b)
Smeg KSEP920X

Need help?

Number of questions: 0

Do you have a question about the Smeg KSEP920X or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Smeg KSEP920X owners to properly answer your question.

View the manual for the Smeg KSEP920X here, for free. This manual comes under the category Exhaust hoods and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Smeg KSEP920X or do you need help? Ask your question here

Smeg KSEP920X specifications

General
Brand Smeg
Model KSEP920X
Product Exhaust hood
EAN 8017709080754
Language English
Filetype PDF
Power
Motor power 200 W
Power consumption (typical) 240 W
Performance
Number of speeds 3
Type of extraction Ducted/Recirculating
Maximum extraction power 615 m³/h
Noise level 71 dB
Design
Number of motors 1
Number of bulbs 2 bulb(s)
Bulb type Halogen
Bulb power 20 W
Product colour Stainless steel
Type Wall-mounted
Filtering
Number of filters 2 pc(s)
Grease filter type Stainless steel
Weight & dimensions
Width 900 mm
Depth 500 mm
Height 968 mm
Height (max) 1478 mm
Height (min) 968 mm

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Smeg KSEP920X.

Is your question not listed? Ask your question here